Walk the Austin slab floor, pick your material, then one crew templates, cuts, and installs. No subcontractors, no handoffs.
Most Kyle kitchens built in the last twenty years came with laminate or tile countertops. When those surfaces wear out or the layout feels dated, homeowners look for something that lasts and cleans up easily. The crew at ATX Granite King handles the whole job, demo, template, fabrication, and install, so there’s only one number to call and one schedule to track.
The posted service area is Austin and the I-35 corridor. Kyle is not on the list, so call the crew to confirm the run to your address before anything is scheduled. They answer seven days a week.
Below is what actually happens when you replace kitchen counters in a Kyle house: what comes out, what goes in, how the backsplash and cabinets are handled, and how to decide on material without overspending on a rental-grade flip.
You pick the slab off a real Austin floor with 299 lots. The same crew that templates your Kyle kitchen also fabricates and installs the tops. Sink cutout and sink set are included. No subcontractors means fewer scheduling gaps and no finger-pointing if something doesn’t line up.
Granite, quartzite, engineered quartz, marble, dolomite, soapstone, porcelain, and semi-precious slabs are all on the floor. For rental-grade or flip-grade stone, the crew works with a partner so you don’t pay for a showpiece slab. Every material has tradeoffs, heat tolerance, porosity, maintenance, so the crew explains what to expect before you buy.
The crew removes the old tops, disconnects and lowers the sink, and hauls off the debris. They template with a digital laser, then return to install the new tops, seal if needed, and set the sink. Backsplashes and cabinets stay in place unless you ask for them to be removed or modified.
Laminate is the most common countertop in Kyle homes built before 2010. It’s glued down, so the crew cuts it into sections to avoid pulling up the particleboard substrate. Tile is chiseled off, and the thinset underneath is ground down so the new tops sit flat. Dated granite or quartz that’s cracked or stained is removed with a diamond blade, and the crew checks for water damage underneath before templating.
If the backsplash is tile or stone, the crew can remove it at the same time as the counters, but it’s an extra step. Laminate or painted drywall backsplashes usually stay in place unless they’re damaged. Cabinets are left alone unless you’re replacing them or need the countertop support reinforced. The crew disconnects the sink, lowers it, and hauls it off with the old tops.
Debris is bagged and taken to a local dump site. The crew sweeps and vacuums the workspace before templating, so you don’t have to worry about dust or sharp edges left behind. If you’re keeping the existing faucet, they cap the lines and protect the finish during the install.
After demo, the crew measures the cabinets with a digital laser. The template accounts for overhang, sink placement, and any uneven spots in the cabinet base. If the old tops were laminate, the crew checks for level, Kyle houses settle, and some older subdivisions have dips that need shimming. The template is sent to the shop, where the slab is cut with a waterjet and polished.
Fabrication takes a few days, depending on the material and workload. Granite and quartzite are cut with diamond blades, while engineered quartz is routed. Edges are shaped and polished in the shop, so the install is faster. The crew gives you written dates for fabrication and install when they quote the job. No same-day or next-day promises, just a schedule that’s realistic for the shop and the crew.
If you’re adding an undermount sink, the crew cuts the hole in the shop and polishes the edges. For a drop-in sink, the cutout is done on-site after the tops are set. The crew seals natural stone in the shop, but you’ll need to reseal it periodically. Engineered quartz doesn’t need sealing, but it can’t handle direct heat or outdoor UV, so it’s not ideal for a Kyle patio kitchen.
Granite is a natural igneous stone that’s hard and heat-tolerant, but it’s porous. In most cases, it needs sealing once a year to resist stains from oil, wine, or coffee. Quartzite is metamorphosed sandstone and is even harder, though some slabs sold as quartzite are softer and behave more like marble. Both are good for Kyle kitchens because they handle heat and don’t etch from acids like lemon or vinegar.
Engineered quartz is non-porous and needs no sealing, but it can be damaged by direct heat from a pot or pan. It’s also not UV-stable, so it’s not a good choice for outdoor kitchens. Marble is calcium-based and etches from acids regardless of sealing, it’s beautiful but high-maintenance. Dolomite is similar to marble but slightly harder, and soapstone is non-porous but scratches easily and needs oiling to keep its color.
Porcelain slabs are heat- and stain-resistant but can chip on the edges. Semi-precious stone is expensive and fragile, so it’s usually reserved for accents. The crew will tell you the honest downsides of each material, so you don’t end up with something that doesn’t fit your cooking habits or budget. For rental-grade or flip-grade stone, they work with a partner to keep costs down without sacrificing durability.
Most Kyle kitchens have a 4-inch tile or laminate backsplash that’s glued to the wall. The crew can remove it during demo if you’re replacing it, but it’s an extra step. If you’re keeping the existing backsplash, they’ll scribe the new countertop to fit tight against it. For a full-height tile or stone backsplash, the crew can template and install it after the counters are in, but it’s a separate job with a separate quote.
Cabinets are left in place unless you’re replacing them or need the countertop support reinforced. The crew checks for level and shims the base if needed. If the old tops were laminate, the crew may need to add a plywood deck to support the new stone. For undermount sinks, the crew cuts the hole in the shop and polishes the edges, then sets the sink after the tops are installed. Drop-in sinks are cut on-site.
If you’re keeping the existing faucet, the crew protects it during install. If you’re upgrading, they’ll install the new one after the sink is set. Outlets and switches are covered during the work, and the crew checks that everything is functional before they leave. The only thing you’ll need to do is seal natural stone periodically, engineered quartz and porcelain don’t need it.
Call the crew to confirm they can run to your Kyle address. The posted service area is Austin and the I-35 corridor, so they’ll let you know upfront if there’s a travel charge. If they can do the job, they’ll set up a time to walk your kitchen, measure, and give you a straight quote. No pressure, no upselling, just the facts on material options and what the job entails.
You’ll pick your slab off a real Austin floor with 299 lots. The crew will show you the tradeoffs of each material, including the ones that are high-maintenance or fragile. For rental-grade or flip-grade stone, they work with a partner to keep costs down. Once you choose, the crew gives you written dates for demo, template, fabrication, and install, no guesswork.
On install day, the crew disconnects the sink, removes the old tops, and hauls off the debris. They template with a digital laser, then return to install the new tops, seal if needed, and set the sink. The whole job is done by the same crew, so there’s only one number to call if something doesn’t line up. They answer seven days a week.
The posted service area is Austin and the I-35 corridor. Kyle sits in Hays County on that corridor, so it is a normal call to take, but it is not on the posted list. Ring (512) 297-7493 and confirm the run to your address before you plan anything around a date.
$38 per square foot, cut, measure, and install included. Jobs over 1,000 square feet: $30 per square foot.
Sink cutout and sink set are included in the fabrication work. Non standard work is still quoted before work begins. Send the rough square footage and the rooms involved, or call (512) 297-7493 for a straight quote.
No. The crew can remove it during demo if you’re replacing it, but it’s an extra step. If you’re keeping the existing backsplash, they’ll scribe the new countertop to fit tight against it. Tile or stone backsplashes can be removed at the same time as the counters, but laminate or painted drywall usually stays in place unless it’s damaged.
The crew checks for level during templating. If there are dips or uneven spots, they’ll shim the base or add a plywood deck to support the new tops. Kyle houses settle over time, so this is common in older subdivisions. The crew won’t install over an unlevel base because it can cause cracks or gaps in the stone.
Yes. The crew disconnects the sink, lowers it, and hauls it off with the old tops. If you’re keeping the sink, they’ll reinstall it after the new tops are in. The same goes for the faucet, they’ll protect it during install and check that it’s functional before they leave. If you’re upgrading, they’ll install the new sink and faucet after the tops are set.
Engineered quartz is non-porous and needs no sealing, but it can be damaged by direct heat from a pot or pan. It’s also not UV-stable, so it’s not a good choice for outdoor kitchens. In most cases, it’s a low-maintenance material, but it’s not as heat-tolerant as granite or quartzite. The crew will tell you the honest tradeoffs before you decide.
The posted service area is Austin and the I-35 corridor. Kyle is not on the list, so call the crew to confirm the run to your address before anything is scheduled. They answer seven days a week and will let you know upfront if there’s a travel charge. No surprises, just a straight answer.
Tell us the rooms, the rough square footage and what you have in mind for kitchen countertop replacement in kyle. You get a number for the whole job, in writing, before anyone cuts anything.